Plumber's Essentials: Your Key to Bathtub Installation

Call


They are making several good points regarding Installing A Bathtub as a whole in the content directly below.


A Step-by-Step Guide to Installing a Bathtub
Mounting a tub isn't precisely brain surgery, yet it does need solid plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old bathtub with a brand-new one is likewise a moderately difficult task. If the old bathtub is readily available, the job can relocate easily; if you need to open up a wall surface to get rid of the old tub and position the new bath tub, the job is a lot harder. In either situation, the project is within a house handyman's abilities, although you will need an assistant to move out the old bathtub as well as set in the new one. Make certain you have qualified yourself for the job and also fit attempting it. Instead of employing a specialist to take control of a halfway-completed job, it is better to take into consideration utilizing one prior to you begin. Chances are you may require an expert plumber to make tube links.
This post will certainly help you install a brand-new bathtub in your bathroom if you have currently purchased a new tub and also do not require to change the arrangement of your previous supply of water pipelines.
Your devices as well as material list should make up the following:


  • New Bathtub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipe Caps


  •  

Removing Old Touches


If you need to change old faucets with new ones as a part of your installment, after that the first thing you must do is separate the water system. After doing so, turn on the taps to drain any type of water staying in the system. The process of removing the existing faucets can be quite bothersome due to the restricted accessibility that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the taps. Have a fabric prepared for the remaining water that will come from the pipes. As soon as the supply pipes have been gotten rid of, use the exact same device to loosen the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from transforming during this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any old sealing compound.
Prior to going on to fit the brand-new taps, contrast the pipe connections on the old taps to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.



Fitting New Taps


If the tails of the brand-new taps are plastic, after that you will need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet and the other end supplies a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly need decreasing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, place the faucet in the placing opening in the bath/basin making sure that the washing machines are in location in between the tap and also the sink. Secure the tap in position with the producer provided backnut. Once the faucet is securely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular tap adapters. The previous type ought to be connected to the faucet finishes initially, tightening just by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.



Mounting the Bath tub


Using both wood boards under its feet, place the bath tub in the required placement. The wooden boards are valuable in equally spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 little factors.
The following objective is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the level and adjusting the feet on the bath tub until the level reviews level.
To install faucets, fit all-time low of the furthest flexible faucet port to the ideal supply pipe by making a compression join; then do the same for the other tap.
Activate the supply of water and check all joints and new pipework for leakages as well as tighten them if required. Fill up the tub and likewise examine the overflow electrical outlet and the typical outlet for leakages.
Lastly, deal with the bathroom paneling as defined in the manufacturer's user's manual. Tiling as well as sealing around the bathtub should wait until the bath tub has been used at least when as this will resolve it into its last setting.



Planning for the Installment


To start with, the supporting structure supplied with the bath needs to be fitted (if called for) according to the producer's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps system to avoid strain on the tub.
Fit the flexible tap ports to the bottom of both faucets making use of 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet through the hole in the bathroom. Use the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you utilize every one of the supplied washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath must currently prepare to be suited its last setting.



Tiling Around the Bath tub


In the location where the bathroom meets the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to break a rigid seal, triggering the water to pass through the wall surface in between the bath and also the tiling, bring about problems with wetness and also feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to blend in your fixtures and installations. They are marketed in tubes as well as cartridges, and can sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of soaked paper or soft rope. Bear in mind to constantly fill the bathtub with water before sealing, to enable the movement experienced when the tub remains in use. The sealant can break fairly very early if you do not consider this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also conveniently offered on the market. It is advisable to fit the ceramic tiles using waterproof or waterproof sticky and grout.


How to Install or Replace a Bathtub


Find Your Dimensions


The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



 

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


Disconnect the Water Supply and Drain Assembly


Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



 

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



 

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


Cut Out the Old Tub


After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



 

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



 

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


Install the New Tub


Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



 

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



 

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



 

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


Secure the Tub


After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



 

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



 

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



 

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


How to Install a Bathtub


Do you appreciate reading up on A Step-by-Step Guide to Installing a Bathtub? Make a remark below. We will be interested to listen to your thoughts about this blog. In hopes to see you back again before long. If you appreciated our blog entry plz be sure to share it. We appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.


24-hour service? Dial here.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Comments on “Plumber's Essentials: Your Key to Bathtub Installation”

Leave a Reply

Gravatar